Veritas Skew Rabbit Plane Revisit

In my previous post I felt like I people would get the ideal I was pretty critical of this plane.  I really do like the plane but it takes some getting used to.  So I'll try and cover it in more detail.

First lets start with the iron.  Most folks I have seen sharpen a skew one of two ways;  Lee Valley Skew jig for the MKII sharpening system or they free hand it.  I bought the jig.  The jig makes the setup fairly fool proof.  I get the iron as sharp as I can.  When your dealing with planes that have to be registered on the work the last thing you want to do is to be trying to shove the plane through the wood.  You must take nice controlled strokes with this plane.

Skew Iron in the Lee Valley Jig

After putting the iron back in the plane it takes a little fettling to get everything lined back up.  This is the system i use.

1. Put the iron in the plane and replace the cap iron.
2. Tighten the cap iron knob a little so that it doesn't come loose while you do your adjusting as you will have the plane upside down a lot.
3. Put the magnet on the side and make sure the edge of the iron lines up with lines up correctly with side of plane.
4. Advance the iron until you can see it while sighting down the plane sole.  It needs to be level.  Once you get it level tighten the cap iron a bit to hold it in position.
5. Break out a straight edge to make sure the knicker, plane iron and side of the plane are all in alignment.  Occasionally I need to move the iron over a bit.  For this i just a small hammer.  When everything is in alignment tighten the cap iron down to hold everything in alignment.  This shouldn't be super tight.  If you over tighten you won't be able to advance and retract the iron.
6. Adjust your knicker blade depth if need be.
7. Now just adjust the depth of cut, fence, and depth stop to the size of your rabbit and you should be ready to go.  I prefer to take light shaving.  Maybe 3 thou or so.  I'll take the extra strokes, it gives me more repeatable results.

Step 3:  Use the magnet to hold the iron in the correct adjustment with the plane side.  

Step 5:  Make sure knicker and iron are in alignment with the side of the plane.  This is where you can see if you have any problems.

Step 6 & 7:  Knicker is at a good working depth.  Can adjust the depth stop to the correct setting now.

Those 7 steps take me less than 5 minutes.  If you don't take the time to do those things, well, that is how "accidents" happen.  

Before we take this puppy for a spin lets keep mindful of a few things that can still mess up your rabbit.  This is where technique come into play.  There are two forces at work work here; keeping the plane registered the work (left hand), and pushing the plane forward (right hand).  

As with any plane we must be sure to you proper technique when pushing the plane.  At the beginning of the cut you must put more pressure holding the front of the plane down.  As you continue with the cut you should move the majority of your pressure to the back tote.  If you are experienced with bench planes this is nothing new to you.

The other issue we must be mindful of is keeping the plane firmly registered and not letting the plane tip from side to side.  I know from experience how easy this is to do, especially on narrow rabbits.  It just requires a little concentration.  If your taking to deep of a cut or have a dull iron can make this very difficult.

Note I'm not using the knob.  It makes the plane to top heavy in my opinion.  I put my thumb firmly on the plane body it is much easier to register.  Plus, I find that I get more feedback from the plane this way.

A nicely cut rabbit.

This is one of those things that takes an hour to describe and 10 minutes to do.  I easily sharpened the iron, fettled with the plane and cut the rabbit in less than 10 minutes.  The plane works great but its does take a little getting used to for a beginner.

The Growing Fleet

While I have been away the fleet has grown considerably.  Thought I might show them off a bit and give you my take on them.  Most of these tools were bought for my class at Marc Adams a while back. I have had a month or so to use them.

Veritas Bevel Up Planes

First off the bevel up planes from Lee Valley.  Some of you may remember I already had the joiner plane.  I just added the jack and smooth planes.  So what did I choose these planes?

• Ease of use.  These are easy planes for a beginner to set up.  There are no chip breakers to fuss with.
• Flexibility.  I can convert any one of these planes to a high angle plane in just a couple minutes by simply resharpening the iron.  So if your planing that Birdseye maple and need a nice high angle plane to reduce tear out...no problem and nothing else to buy.  Also the irons in these planes are interchangeable.  So I can use my smoother iron in my jack plane if need be.  This has come in handy a couple times.  I have put my smoother iron (typically set on a higher angle) in my joiner when the wood wasn't cooperating and was leaving deep tear out.
• Cost.  Because I had several tools to buy I couldn't afford the Lie Nielsen models.  Having used both the Lie Nielsen and Veritas versions of the bevel up plane I would say you get much more bang for your buck with the Veritas.

I have been very pleased with these planes.  The A2 irons take and hold a edge.  I can pull shaving so thin that I don't even call them shavings, I call them fluff.  The fit and finish was superb.  On the down side there are some things I don't like also.  The Norris style blade adjuster on these planes can be a pain.  The pivot points for the adjuster are so close together that the slightest movement will move the iron side to side dramatically.  I have learn to overcome this demon but it does take some getting used to.  You give up the ability to just sliding your finger down and turing the blade depth knob in between cuts.  You must be careful when you turn the blade adjustment knob not to move the blade side to side. I don't normally adjust the blade that much so it hasn't been a huge deal for me, more of an inconvenience.  My only other complaint is that the smoother and joiner (especially the joiner) doesn't have machined sides so that you can use them on your shooting board.  The jack planes does have machined sides and is fairly renowned as a great shooting board plane.  It would have been nice to have this capability with the other planes.  I'm not sure if this was done to save money or to reduce the amount of unpainted steel you have to keep rust free.  Never the less, this is something that I wish Robin Lee would take a look at.

Overall, I really like the planes and would have no reservations recommending them to someone.

Veritas Small Plow Plane, Veritas Moving Rabbit Plane, Veritas Large Router Plane

This is a mixed bag of specialty planes by Veritas.  We'll discuss them individually.

• Small Plow Plane.  I don't have a lot to say about this plane.  The product is has a great fit and finish to it.  I got a set of different width blades that seem to work great.  The fence has always locked perfectly square for me.  There honestly aren't a lot of new planes out there to compare it to.  I'm not sure why Lie Nielsen isn't already making a plow.
• Moving Skewed Rabbit (Fillister) Plane.  This plane takes a bit of practice to get the hang of.  We used this plane in our class and I heard several people curse it's name, including me.  Its not because it's a bad plane.  Most folks brought new planes with them and they had very little experience, if any, using the plane.  This plane can be awkward to set up.  The blade has to be flush with the wall of the plane or your rabbit will just get wider and wider and the plane will be hard to push.  I come up with a "jig" to help me keep this aligned while I tighten everything up.  If you look at the photo above you will see a silver metal disk on top of the plane.  Its a rare earth magnet.  By placing the rare earth magnet on the wall of the plane it will pull and hold the iron in position.

The magnet holds the iron in alignment with the wall of the
plane so you can adjust blade depth and tighten everything up.

• I store the magnet on top of the plane when not in use.  Works pretty nicely.  The problem i had with the plane was that my knicker was out of adjustment.  Chris Schwarz spotted this instantly and corrected it for me.  Turns out someone didn't read the directions.  Even after you get the plane adjusted correctly it takes some time to get a technique that works for your.  Its very easy no let the plane tip and mess up your rabbit.  Chis showed me that he removes the knob from his so he can more easily use the plane body to guide the plane.  The handle seems to have to high of a center of gravity and makes the plane easier to tip.  Don't let me give you the ideal that I don't like the plane.  The plane works but there is a larger learning curve than other planes.  When I get a messed up rabbit, I am normally the problem.  Perhaps I'll do a write up just on this plane and how to use it.
• Large Router Plane.  This plane is much more straight forward.  It just works.  I chose this plane over the Lie Nielsen because of blade selection.  This plane has a wider selection of blades including the spear point blade which I don't think is available from Lie Nielsen.  This is another product that I feel you get more bang for your buck versus the Lie Nielsen.  I really must by this planes little brother the small router plane.  The biggest problem i have with it is that keep trying to use it in small places where it won't fit.  

Czech Edge Birdcage Awl and Marking Knife

I also got a couple of layout tools from Czech Edge, the birdcage awl and a making knife.  I have enjoyed the tools.  They have a nice fit and finish and have performed as advertised.  One thing that shocked me was the size of the birdcage awl.  For some reason I was expecting something smaller.  It resembles a really nice prison shank.  It does a great job starting holes for drill bits or making locations for nails and screws.  I used the marking knife my class for laying out dovetails and it did a great job.  The blade is nice and thin to get into those tight pins.  The only suggestion I would make is that they need shape the handle more so your fingers have more to grip.  I found my fingers slipping down the shaft a bit.  Overall great tools that I would recommend to others.

Hide Glue, why does it keep hanging around?

During my recent class at Marc Adams I got to use hide glue for the first time.  Its been one of those things I have always wanted to try but had never gotten around to.  Hide glue can be a little intimidating, especially with all the stories out there.  I often hear stories where create all these crude concoctions.  It brings to mind a which over a kettle adding a pinch of lizards gizzards.

It isn't surprising that these things happen.  You have to expect people to tinker with your chemistry after you have been around for 4000+ years.  Even how to mix the glue up seems to be a bit of a mystery.  Some folks do it one way and other do the opposite.  Like I said, fairly intimidating.

Hide glue is like sharpening, the more information (and is there a lot of it!) you get the less you know.  You don't need any fancy equipment.  If you are just wanting to try it out you can use a stove, sauce pan, and candy thermomenter and you will do fine.  That is, if your wife doesn't catch you.

If you want to get your feet wet there is another option, the option we used at Marc Adams.  We used Old Brown Glue.  This is simply hide glue that has been mixed with urea so that it will remain liquid (or somewhat liquid) at room temperature.  The glue has a one year shelf life but that can be extended if you store it in the fridge.  When your ready to glue up simply heat the glue to get it to the right consistency and then apply it.  It doesn't have to be that warm.  Simply putting it in a window sill on a summer day will do just fine.  But in the winter you might want to invest in a small $10 croc pot.

I have been using hide glue since the class and love it.  I feel more at ease using it.  The are the benefits I have seen so far...

• No fuss clean up.  Simply take a damp rag and you can remove excess glue easily.  Also works great at getting it off the workbench, clamps, etc.
• No more glue blotches when applying stain.
• Has the right consistency.  The glue has sort of a snot consistency.  Seems to stick to the wood better and you get some initial tack.

Obviously this is the glue for all situations but my bottle of Titebond is getting pretty lonely.  I urge anyone who hasn't tried hide glue to give it a shot.  You'll be glad you did.

Photo by Chris Schwarz

By Hammer & Hand

I recently attended the Marc Adams School Of Woodworking and attended a class taught by Chris Schwarz called By Hammer & Hand.  This class was based on a book compiled by Joel Moskowitz and Chris Schwarz called The Joiner and the Cabinetmaker.  The book consists of a reprint of and old text by the same name plus background and discussion by Joel and Chris.  In this book we follow the early career of a cabinetmaker apprentice.  The project we focused on was the second project the apprentice was allowed to build on his own, the school masters box.

Let me start with my experience at the Marc Adams School.  This was a week long class and it was a great experience.  I had never taken a woodworking class and didn't know what to expect.  If you have a little vacation time coming, it's worth the money.  Everyone at the school was very nice.  Our shop assistants that helped out were very knowledgeable and a great help.  The lady's that worked in the lunchroom put out very tasty food, not your typical cafeteria grub.  If you are considering attending for the first time, give me a shout and I can give you and idea of what to expect.

I wasn't sure how much I would get out of the class.  I thought I might not learn a whole lot but it would be a good time and fun to hang out with other woodworkers.  I knew how to dovetail, that seemed to be the greatest hurdle for this project.  I was wrong.  I did learn a few things, more importantly, I learned a little about the process.  I spent a lot of time focusing on grain direction, wood orientation, and how to use a woods natural beauty to your advantage.  I wasn't able to finish my box for a few reasons.  One was I had a difficult wood to work with and it took more time to lay out everything.  I also had to spend a lot of time in wood prep.  Most folks brought their wood already planed and ready to go.  I brought rough cut, highly figured wood that demanded some careful planning.

My box still needs the moldings and hinges.  I am looking at having a local blacksmith make the hinges and hope to have the box completed soon.  The box is made from spalted quilted maple.  Very beautiful wood.  It took a while to wrap the spalting and to really take advantage of the figure.

Chris did a great job with the class and I think we all loved our time there.  Here a quick video Chris shot of the class...